China supplier Zjt-70 70L/S Zj-70 1.5kw Tri-Lobe Roots Vacuum Pump vacuum pump ac system

Product Description

 

Working principle

Roots vacuum pump is a kind of rotary positive-displacement type of pump. The 2 three-lobe rotors keep a certain gap with the housing, and the 2 rotors mesh with each other and keep a certain gap when they rotate in the housing through a pair of synchronous reverse rotation high-precision gears. The diagram on the right shows the structure principle of the pump, from diagram I to IV, the rotor rotates in the house and completes 1 suction and discharge process.
The Roots vacuum pump with three-lobe rotors has technical advantages over the traditional two-lobe rotors in terms of pumping efficiency, maximum allowable differential pressure, temperature, vibration, noise and other major performances.

 

Main features

Compared with the traditional two-lobe Roots vacuum pump, there are below advantages:
1. Much higher efficiency, lower temperature, vibration and noise.
2. More stable and reliable, more convenient to use and maintain.
Other features:
1. Lower failure due to the rotors are fixed and no axial run-out.
2. High-precision transmission gear and precision rolling bearing are used, resulting in low noise and smooth operation.
3. The main shaft use special mechanical seal to ensure oil-free pump chamber.
7. Mechanical seal, oil seal, piston ring labyrinth seal and other types of seal can be used for end cover.
8. It is used in pump combinations together with rotary vane vacuum pump, reciprocating pump, liquid ring pump, dry screw pump and other types of backing pumps to meet various process requirements.

Applications

The advantage of Roots vacuum pump is that it has large pumping efficiency even at low inlet pressure, but ordinary Roots vacuum pump can’t be used alone, it must be used in pump combinations together with the backing pumps. The Roots vacuum pump can be started only after the pressure in the system is pumped to the allowable starting pressure of the Roots vacuum pump by the backing pump.
According to different working pressure and process conditions, the backing pump of Roots vacuum pump can be rotary vane vacuum pump, liquid ring vacuum pump, dry screw vacuum pump and so on. The performance of Roots vacuum pumps are different when combination with different backing pumps.
Roots vacuum pumps are mainly used in any vacuum system requiring large pumping speed and rough and medium vacuum (103-10-2Pa), such as: vacuum coating, vacuum welding furnace, vacuum heat treatment furnace, large space simulation test, microelectronics and integrated circuits, lamp and bulb manufacturing, laser manufacturing, vacuum packaging, centralized pumping system, various chemical processing, vacuum degassing vacuum deaeration, vacuum dehydration, vacuum CZPT drying, vacuum distillation.

Product Parameters

Model Nominal pumping speed(50Hz) Ultimate pressure Maximum allowable pressure difference Nominal motor rating (50Hz)   Nominal motor speed  (50Hz)  Suction Connection size Discharge Connection size Weight Backing pump recommended
L/s Pa Pa Kw rpm mm mm Kg
ZJT-70 70 ≤0.5 ≥1.2*104 1.5 1450 100 80 165 DVP180 or DSP140
ZJT-150 150 ≤0.5 ≥1*104 3 2900 100 80 165 DVP360 or DSP280
ZJT-300 300 ≤0.5 ≥8*103 4 2900 160 100 275 DVP540 or DSP540
ZJT-600 600 ≤0.5 ≥6*103 5.5 2900 200 160 420 DVP540 or DSP540
ZJT-1200 1200 ≤0.05 ≥5*103 11 2900 250 200 980 ZJTQ-300+DVP540
ZJT-2500 2500 ≤0.05 ≥4*103 18.5 2900 320 250 1800 ZJTQ-600+DVP540
ZJT-5000 5000 ≤0.05 ≥3*103 37 1450 300 300 3580 ZJTQ-1200+DVP800

Note:
1. The pumping speed refers to the maximum pumping speed measured at the inlet pressure of the Roots vacuum pump in the range of 67 pa to 2.67 pa under the conditions of the recommended backing pump. (see p Pumping speed diagram)
2. The ultimate pressure is the lowest value of the stable air partial pressure measured at the pump inlet with a compression vacuum gauge after full pumping without any additional container and no air inlet under the condition of the recommended backing pump.
3. The data of the above table is obtained under the condition of using the recommended backing pump, users can choose different backing vacuum pumps according to different situations, but the main performance index will be changed.
 

Pressure diagram

 

 

Dimension

 

Model L L1 L2 L3 H H1 H2 H3 A A1 A2 D D1 D2 N-M d d1 d2 n-m
ZJT-70 730 191 330 360 270 252   40 256   214 Ф80 Ф125 Ф145 8-M8 Ф50 Ф90 Ф110 4-M8
ZJT-150 938 . 273 132 184 350 330 116.5 30 392 358 300 Ф100 Ф145 Ф165 8-M8 Ф80 Ф125 Ф145 8-M8
ZJT-300 1032 323 185 259 405 385 135 40 455 420 350 Ф150 Ф200 Ф225 8-M10 Ф100 Ф145 Ф165 8-M8
ZJT-600 1282 405 220 304 520 495 165 35 587 548 450 Ф200 Ф260 Ф285 12-M10 Ф150 Ф200 Ф225 8-M10
ZJT-1200 1573 473 296 392 650 625 218.5 58 722 678 560 Ф250 Ф310 Ф335 12-M10 Ф200 Ф260 Ф285 12-M10
ZJT-2500 1890 594 440 552 730 700 220 55 858 810 660 Ф320 Ф395 Ф425 12-M12 Ф250 Ф310 Ф335 12-M10

FAQ

Q: What information should I offer for an inquiry?
A: You can inquire based on the model directly, but it is always recommended that you contact us so that we can help you to check if the pump is the most appropriate for your application.

Q: Can you make a customized vacuum pump?
A: Yes, we can do some special designs to meet customer applications. Such as customized sealing systems, speical surface treatment can be applied for roots vacuum pump and screw vacuum pump. Please contact us if you have special requirements. 

Q: I have problems with our vacuum pumps or vacuum systems, can you offer some help?
A: We have application and design engineers with more than 30 years of experience in vacuum applications in different industries and help a lot of customers resolve their problems, such as leakage issues, energy-saving solutions, more environment-friendly vacuum systems, etc. Please contact us and we’ll be very happy if we can offer any help to your vacuum system.

Q: Can you design and make customized vacuum systems?
A: Yes, we are good for this.

Q: What is your MOQ?
A: 1 piece or 1 set.

Q: How about your delivery time?
A: 5-10 working days for the standard vacuum pump if the quantity is below 20 pieces, 20-30 working days for the conventional vacuum system with less than 5 sets. For more quantity or special requirements, please contact us to check the lead time.

Q: What are your payment terms?
A: By T/T, 50% advance payment/deposit and 50% paid before shipment.

Q: How about the warranty?
A: We offer 1-year warranty (except for the wearing parts).

Q: How about the service?
A: We offer remote video technical support. We can send the service engineer to the site for some special requirements.

After-sales Service: Online Video Instruction
Warranty: 1 Year
Oil or Not: Oil Free
Structure: Rotary Vacuum Pump
Suction Connection Size: 100 mm
Discharge Connection Size: 80 mm

Vacuum Pump

Types of vacuum pumps

A vacuum pump is a device that draws gas molecules from a sealed volume and maintains a partial vacuum. Its job is to create a vacuum in a volume, usually one of several. There are several types of vacuum pumps, such as root pumps, diaphragm pumps, rotary piston pumps, and self-priming centrifugal pumps.

The diaphragm pump is a dry positive displacement vacuum pump

Diaphragm pumps are a versatile type of vacuum pump. They can be installed in a variety of scenarios including container emptying, positive suction, and simultaneous fluid mixing. Their performance depends on the stiffness and durability of the diaphragm, which in turn depends on the material.
They have good performance when running in dry mode. Diaphragm pumps work very similarly to the human heart, which is why they are often used to create artificial hearts. In addition, the diaphragm pump is self-priming and has high efficiency. They are also capable of handling the most viscous liquids and are used in almost all industries.
However, this type of pump has several disadvantages. One of them is that they are difficult to restart after a power outage. Another disadvantage is that they can generate a lot of heat. Fortunately, this heat is carried away by airflow. However, this heat builds up in the multistage pump. If this happens, the diaphragm or motor may be damaged. Diaphragm pumps operating in two or more stages should be fitted with solenoid valves to maintain vacuum stability.
Diaphragm pumps are a good choice for drying processes where hygiene is important. These pumps have check valves and rubber or Teflon diaphragms. Diaphragm pumps are also ideal for high viscosity applications where shear sensitivity is important.

Roots pumps are dry method centrifugal pumps

Roots pumps use a vane rotor pump with two counter-rotating vanes that move in opposite directions to move the gas. They are often the first choice for high-throughput process applications. Depending on the size and number of blades, they can withstand up to 10 Torr.
Centrifugal pumps have several advantages, including the ability to handle corrosive fluids and high temperatures. However, when choosing a pump, it is essential to choose a reputable manufacturer. These companies will be able to advise you on the best pump design for your needs and provide excellent after-sales support. Roots pumps can be used in a wide range of industrial applications including chemical, food, and biotechnology.
The Roots pump is a dry centrifugal pump whose geometry enables it to achieve high compression ratios. The screw rotors are synchronized by a set of timing gears that allow gas to pass in both directions and create a compressed state in the chamber. The pre-compressed gas is discharged through a pressure connection and cooled with water. Some pumps are also able to accept additional cooling gas, but this should be done with caution.
The size of the impeller plays an important role in determining the pump head. The impeller diameter determines how high the pump can lift the liquid. Impeller speed also affects the head. Since the head is proportional to the specific gravity of the liquid, the available suction pressure will be proportional to the density of the liquid. The density of water is about 1.2 kg/m3, and the suction pressure of the centrifugal pump is not enough to lift the water.

The rotary vane pump is a self-priming centrifugal pump

A rotary vane pump is a centrifugal pump with a circular pump head and a cycloid cam that supports the rotor. The rotor is close to the cam wall, and two side plates seal the rotor. Vanes in vane pumps are installed in these cavities, and the rotor rotates at high speed, pushing fluid in and out of the pump. The pump offers several advantages, including a reversible design and the ability to handle a wide variety of clean fluids.
Agknx Pumps manufactures a wide range of vane pumps that combine high performance, low cost, and easy maintenance. These pumps handle medium to high viscosity liquids up to 500 degrees Fahrenheit and 200,000 SSU.
The suction side of the rotary vane pump has a discharge port, and the valve prevents the backflow of the discharge air. When the maximum pressure is reached, the outlet valve closes to prevent the backflow of exhaust gas. The mechanical separation step separates the oil from the gas in the pump circuit and returns the remaining oil particles to the sump. The float valve then reintroduces these oil particles into the oil circuit of the pump. The gas produced is almost oil-free and can be blown out of a pipe or hose.
Rotary vane pumps are self-priming positive displacement pumps commonly used in hydraulic, aeration, and vacuum systems. Unlike gear pumps, rotary vane pumps can maintain high-pressure levels while using relatively low suction pressures. The pump is also very effective when pumping viscous or high-viscosity liquids.
Vacuum Pump

Rotary piston pumps are dry method positive displacement pumps

Rotary piston pumps are dry positive displacement pumps designed to deliver high-viscosity fluids. They are capable of pumping a variety of liquids and can run dry without damaging the liquid. Rotary piston pumps are available in a variety of designs. Some are single shafts, some are two shafts and four bearings.
Positive displacement pumps operate slower than centrifugal pumps. This feature makes the positive displacement pump more sensitive to wear. Piston and plunger reciprocating pumps are particularly prone to wear. For more demanding applications, progressive cavity, diaphragm or lobe pumps may be a better choice.
Positive displacement pumps are typically used to pump high-viscosity fluids. This is because the pump relies on a mechanical seal between the rotating elements and the pump casing. As a result, when fluids have low viscosity, their performance is limited. Additionally, low viscosity fluids can cause valve slippage.
These pumps have a piston/plunger arrangement using stainless steel rotors. Piston/piston pumps have two cavities on the suction side. The fluid then flows from one chamber to the other through a helical motion. This results in very low shear and pulsation rates. The pump is usually installed in a cylindrical housing.

Rotary vane pump corrosion resistance

Rotary vane vacuum pumps are designed for use in a variety of industries. They feature plasma-treated corrosion-resistant parts and anti-suck-back valves to help reduce the number of corrosive vapors entering the pump. These pumps are commonly used in freeze dryers, vacuum ovens, and degassing processes. The high flow rates they provide in their working vacuum allow them to speed up processes and reduce the time it takes to run them. Plus, they have energy-efficient motors and silent volume. <br/While rotary vane vacuum pumps are relatively corrosion resistant, they should not be used for aggressive chemicals. For these chemicals, the most suitable pump is the chemical mixing pump, which combines two types of pumps to improve corrosion resistance. If the application requires a more powerful pump, a progressive cavity pump (eg VACUU*PURE 10C) is suitable.
Oil seals used in rotary vane pumps are important to pump performance. The oil seal prevents corrosion of the aluminum parts of the rotary vane pump and prolongs the service life. Most rotary vane vacuum pumps have a standard set of components, although each component may have different oil seals.
Rotary vane vacuum pumps are the most common type of positive displacement pump. They provide quiet operation and long service life. They are also reliable and inexpensive and can be used in a variety of applications.
Vacuum Pump

Roots pumps are primarily used as a vacuum booster

Root vacuum pumps are mainly used as vacuum boosters in industrial applications. They need a thorough understanding of operating principles and proper maintenance to function properly. This course is an introduction to Roots vacuum pumps, covering topics such as pump principles, multi-stage pumps, temperature effects, gas cooling, and maintenance.
Roots pumps have many advantages, including compact and quiet operation. They do not generate particles and have a long service life. They also don’t require oil and have a small footprint. However, Roots pumps have several disadvantages, including relatively high maintenance costs and low pumping speeds near atmospheric pressure.
Root vacuum pumps are often used with rotary vane vacuum pumps. They work on the same principle, the air enters a conveying unit formed by two rolling pistons in the housing. The piston heads are separated from each other, and the air passes through the unit without being reduced until it is discharged. When the air in the next unit reaches a higher absolute pressure, it is expelled from the last unit.
Roots pumps can be classified as sheathed or sealed. Roots pumps with sealed motors are suitable for pumping toxic gases. They have less clearance between the stator and motor rotor and have a sealed tank.

China supplier Zjt-70 70L/S Zj-70 1.5kw Tri-Lobe Roots Vacuum Pump   vacuum pump ac system	China supplier Zjt-70 70L/S Zj-70 1.5kw Tri-Lobe Roots Vacuum Pump   vacuum pump ac system
editor by CX 2023-08-29